3GM_BISTATIC_RADAR | characterization of the surface by determination of roughness, dielectric constant of surface material and material density. The chosen antenna points towards surface, radio signal reflects from surface and received on ground. USO unmuted | 3GM |
3GM_GRAVITY | KaT and HAA for gravity science | 3GM |
3GM_GRAVITY_FOR_EPHEMERIDES | KaT ON during communication windows | 3GM |
3GM_HAA_CALIBRATION | HAA in CALIBRATION mode
Duration: 50min | 3GM |
3GM_HAA_STANDBY | HAA in STANDBY mode | 3GM |
3GM_RADIO_OCCULTATIONS | The radio science experiment 3GM, with its dual-frequency radio links (X and Ka-band) referenced to an ultrastable oscillator (USO), is performed as JUICE spacecraft moves in and out of occultation. USO unmuted, HAA in NOMINAL SCIENCE.
Note that 2 other options exist for torus occultations but are not (yet) defined in the database | 3GM |
3GM_USO_ON | USO is SWON and muted | 3GM |
DRAFT_3GM_BSR | Characterisation of the surface by determination of roughness, dielectric constant of surface material and material density. The chosen antenna points towards surface, radio signal reflects from surface and received on ground. USO unmuted.
The HAA shall be ON to calibrate the sloshing potentially excited by pointing the HGA toward a moon’s Surface. | 3GM |
DRAFT_3GM_GRAVITY_FLYBYS | Gravity measurement during flyby requires the use of the MGA.
KaT and HAA should be operating during gravity measurement
USO assumed to be ON during the full tour: this should be defined in the scenario set-up and not at 3GM observation approach.
HAA should be in STANDBY mode at least 48 hours before the gravity measurement.
The observation should start with 1 hour of HAA in CALIBRATION mode. KaT starts with 10min of warm-up. | 3GM |
DRAFT_3GM_GRAVITY_GCO500_200 | Gravity measurement during GCO500 and GCO200 will use the HGA during downlink sessions. If not possible, it will use the MGA. KaT and HAA should be operating during gravity measurement. USOis OFF during this phase (except in case of BSR opportunity). HAA should be in STANDBY mode at least 48 hours before the gravity measurement. The observation should start with 1 hour of HAA in CALIBRATION mode. KaT starts with 10min of warm-up. | 3GM |
DRAFT_3GM_GRAVITY_TOUR | KaT and HAA should be operating during gravity measurement
USO assumed to be ON during the full tour: this should be defined in the scenario set-up and not at 3GM observation approach.
HAA should be in STANDBY mode at least 48 hours before the gravity measurement.
The observation should start with 1 hour of HAA in CALIBRATION mode. KaT starts with 10min of warm-up. | 3GM |
DRAFT_3GM_OCCULTATION | The radio science experiment 3GM, with its dual-frequency radio links (X and Ka-band) referenced to an ultrastable oscillator (USO), is performed as JUICE spacecraft moves in and out of occultation. Occultations occur throughout the jovian tour, but their phasing is not always synchronized with the timing of dedicated Jupiter observations by the other orbiter experiments. USO unmuted, HAA in NOMINAL SCIENCE.
Note that 2 other options exist for torus occultations but are not (yet) defined in the database | 3GM |
GAL_GAN_OFF_POINTING | specific observation for polar geometry with off-pointing w.r.t Nadir during GCO500.
Only to be executed TBD time. Similar profile than GAL_MONITORING_GAN but with off nadir pointing request | GALA |
GAL_HR_FB | High resolution data acquisition around FB closest approach. GALA will measure the time of flight between firing and receiving the returned laser signal | GALA |
GAL_HR_TARGET_GAN | Region of Interest Observation at Ganymede | GALA |
GAL_IDLE | Transition from OFF to IDLE mode (and IDLE to OFF) | GALA |
GAL_LR_FB_ALBEDO | GALA will passively measure the reflectance of the illuminated hemisphere of the satellite during flyby nadir phase.GALA will operate in passive albedo mode (DiagRx) | GALA |
GAL_MONITORING_GAN | GALA will measure the time of flight between firing and receiving the returned laser signal during Ganymede phase | GALA |
GAL_WARMUP_GAN | needed right before ANY science observation from GALA during Ganymede phase
Duration: 90min | GALA |
JAN_CONFIG | No observations, but instrument ON for thermal stabilization of the complete electronics (PEU and detector are ON) and for setting the observation sequences and between two observation sequences that are too close to switch the detector OFF. | JANUS |
JAN_IDLE | No observations, but instrument ON for thermal stabilization before observations or between two observation phases that are too close to switch the instrument OFF. | JANUS |
JAN_OFF | No observations, instrument OFF. | JANUS |
JAN_SCI_INERTIAL | TBW | JANUS |
JAN_SCI_LIMB | Children observations defined during scenarios
│ ├── JAN_SCI_LIMB_HAZES
│ ├── JAN_SCI_LIMB_HIGHPHASE
│ ├── JAN_SCI_LIMB_POLAR_SOUTH | JANUS |
JAN_SCI_PB | Observations of single or multiple frames with a pointing offset wrt to nominal S/C pointing (e.g., wrt nadir-looking while in G orbit, during FB or while in Jupiter orbit) | JANUS |
JAN_SCI_RASTER | Observations of multiple frames in (m x n) positions targeted with a raster pointing of the S/C. The raster is done with a stop-and-go approach: the S/C maintain an inertial pointing allowing images acquisitions, then perform a slew to the new position and repeat the cycle till the (m x n) raster is completed. To be used while in J orbit or during FBs (out from CA phase).
Children observation defined during scenarios:
│ ├── JAN_SCI_RASTER_AMALTHEA_HIGH_RES
│ ├── JAN_SCI_RASTER_AURORAS
│ ├── JAN_SCI_RASTER_FEATURES
│ ├── JAN_SCI_RASTER_GLOBAL_MAP
│ ├── JAN_SCI_RASTER_HIGH_RES_MAP_JOINED_SET_003_S007_01_S00P01.def
│ ├── JAN_SCI_RASTER_HIGH_RES_MAP
│ ├── JAN_SCI_RASTER_IO_TRANSIT_001_PART_1_S007_01_S00P01.def (name non compliant)
│ ├── JAN_SCI_RASTER_IO_TRANSIT_001_PART_2_S007_01_S00P01.def (name non compliant)
│ ├── JAN_SCI_RASTER_IO_TRANSIT_001_S007_01_S00P01.def
│ ├── JAN_SCI_RASTER_LIGHTING_MAP
│ ├── JAN_SCI_RASTER_POLAR_SOUTH | JANUS |
JAN_SCI_SLEW | Observations of multiple frames in (m x n) positions targeted with a raster pointing of the S/C made with a continuous slew. The raster is done with continuous slew approach: images are acquired while the S/C is slewing; slew rate shall be adapted with the instrument angular sampling and the integration time. To be used while in J orbit or during FBs (out from CA phase) | JANUS |
MAG_BURST | Operation of J-MAG in burst mode (measurement at rate of 128 vectors/s) starting 10 minutes before and ending 10 minutes after a predicted crossing of a thin current sheet in Ganymedes magnetosphere (magnetopause/magnetotail current sheet). | JMAG |
MAG_BURST_FIB_FOB | Burst observation mode without scalar sensor | JMAG |
MAG_CALROLL | Campaign of spacecraft rolls to allow calibration of J-MAG magnetic field measurements. J-MAG will take data in gradiometer mode continuously while the spacecraft rolls about two principal axes, in regions where the Jovian magnetic field is >100 nT. Spacecraft rolls about two principal axes. 3 rolls of 360° about first axis at 0.5 rev/hr, then 3 rolls about the second axis (also at 0.5 rev/hr). The spacecraft rotation axes must always make an angle with the ambient magnetic field between 20° and 160°. | JMAG |
MAG_CONTINOP | measure the magnetic field in normal mode (at a rate of 32 vectors/s) continuously | JMAG |
MAG_CONTINOP_FIB_FOB | J-MAG will measure the magnetic field in normal mode (at a rate of 32 vectors/s) continuously with SCA not operating | JMAG |
MAG_CONTINOP_FIB_FOB_LIGHT_ONLY | JMAG mode (FIB FOB Light Only), this mode ensures that while FIB and FOB are collecting science the Scalar sensor also has power to its laser but is not collecting science data. This helps to protect the fibres from radiation damage, necessary for the Europa phase due to its radiation environment. | JMAG |
MAG_DL | This observation is introduced to characterize JMAG operations during downlink times where power resources from the SC may be more limited, and where SC attitude is driven by operational constraints. Only MAGOBS and MAGIBS are operating. | JMAG |
MAG_DL_FOB | This observation is introduced to characterise JMAG operations during downlink times where power resources from the SC may be more limited, and where SC attitude is driven by operational constraints Only MAGOBS is operating. | JMAG |
MAG_DL_FOB_LIGHT_ONLY | This observation is introduced to characterise JMAG operations during downlink times where power resources from the SC may be more limited, and where SC attitude is driven by operational constraints In this particular observation FOB fluxgate is powered on with FSC as light-only. | JMAG |
MAG_DL_LIGHT_ONLY | This observation is introduced to characterise JMAG operations during downlink times where power resources from the SC may be more limited, and where SC attitude is driven by operational constraints.
In this particular observation FIB & FOB fluxgates powered on with FSC as light-only. | JMAG |
MAJ_Amalthea | S/C pointing Amalthea preferentially near maximal elongation of (2.54 R_J), 2 hemispheres, MAJIS spatial windowing (16 rows)
pointing: OFF-NADIR, S/C pointing Amalthea at 2.54 R_J while maintaining horizontal orientation of MAJIS slit
satellite orientation: Maintaining horizontal orientation of MAJIS slit, MAJIS scan mode activated for vertical sampling centered on the satellite (10 lines)
Duration: 100 sec for one hemisphere | MAJIS |
MAJ_BORESIGHT_ALIGNEMENT | Star sequence for geometrical calibration.
A star is initially pointed using the MAJIS boresight, then MAJIS is operated with the scan mechanism at high resolution (1/3 of IFOV) over 18 lines centered in the star. Then this operation is successively observed after 4 S/C repointings of 1.5° around X and Y.
Pointing : inertial
Satellite orientation: S/C pointing the star and MAJIS scans
Duration: 18 to 180 sec per position (5 positions in total)+ stabilization time for repointing not taken into account | MAJIS |
MAJ_FLYBY_HR | High resolution pubshbroom flyby observations of satellite dayside surfaces bracketing closest approach. Satellite offsets around Y (off-track pointing) axis during or prior to observation allow near-nadir pointing of specific regions. Motion compensation or MAJIS scan is achieved using the MAJIS internal pointing mirror depending on the S/C speed and distance. Binning can be applied may be required near C/A.
Pointing: NYS, NADIR or OFF_NADIR after offset around Y (‘motion compensation PB’).
Satellite orientation: MAJIS slit across track, Satellite offsets around Y (off-track pointing) axis possible.
Duration: 20 to 130 sec | MAJIS |
MAJ_FLYBY_MEDRES | Flyby observations of the satellite surface with vertical (N-S) slews or MAJIS scan providing medium spatial resolution (e.g.resolution from 3 km to 1 km/pixel for Ganymede). Perform when the S/C moves slowly from approach YS phase to PB phase and during PB phase.
Pointing: NYS, NADIR or OFF_NADIR after offset around Y ( ‘motion compensation PB’).
Satellite orientation: MAJIS slit across track. Satellite offsets around Y (off-track pointing) axis or around X axis (for slew).
Duration: a few minutes maximum | MAJIS |
MAJ_GCO500_HR | Observations in true push-broom of specific targets on the surface using motion compensation with the scanner
30 km cross-track x 8.7 km along-track @ 75 m/pixel
30 km cross-track x 17.4 km along-track @ 150 m/pixel (spatial binning x2)
Pointing: Nadir pointing, NYS ( ‘motion compensation PB’)
Satellite orientation: MAJIS slit perpendicular to the ground-track
Duration: One acquisition: 60 sec; switch-on procedure: 10 minutes (TBC) | MAJIS |
MAJ_GCO500_LIMB | Mapping of selected areas on the dayside limb at resolutions of about 300 m at different latitudes (~30° in lat/lon from the nadir) to study variability of the exospheric processes (sputtering, photodissociation, sublimation). MAJIS scanning at different latitudes of the diurnal limb; a minimum of 3 (north,equat,south) x 2 (dawn, dusk) positions.
Pointing: S/C limb tracking at locations where the slit is tangent to the limb
satellite orientation: Off-nadir orientation, Slit tangent to the limb
Duration: 600 sec per cube | MAJIS |
MAJ_GCO5000_AURORA | Observations at auroral latitudes (30-35° N-S), at least in the dawn and dusk sides of Jovian magnetosphere.
Mapping at spatial resolution of about 1 km using the MAJIS scan
Pointing: S/C limb; no requirements on the slit orientation
Saletllite orientation: Off-nadir orientation | MAJIS |
MAJ_GCO5000_GLOBAL | Systematic mapping performed with cross-track binning by 4 during circular phase (~120 days)
3 km/pixel, 300x300 km swaths, spatial binning x 4.
Pointing: YS, Nadir
Satellite orientation: MAJIS slit at a slant with the ground track except at the equator
Duration: 4H per orbit (one cube: 6 min) | MAJIS |
MAJ_GCO5000_LIMB | Latitudinal scanning of the diurnal limb at 1 km at different latitudes; study of the variability of the exospheric processes (sputtering, photodissociation, sublimation). Observe polar (north/south) and equatorial latitudes ; perform long-term and high-temporal-resolution monitoring.
Pointing: S/C limb tracking at locations where the slit is tangent to the limb
Satellite orientation: Off-nadir orientation, Slit tangent to the limb
Duration: 600sec | MAJIS |
MAJ_GCO5000_REGIONAL | During circular phase (~120 days), regional mapping of the surface of Ganymede, bridging the gap in resolution between systematic global mapping and HR ROI's observed at GCO-500.
750 m/pix (no spatial binning), 300x300 km swaths
Pointing type: YS, NADIR
Satellite orientation: MAJIS slit at a slant with the ground track except at the equator
Duration: 6min | MAJIS |
MAJ_GEO5000 | During elliptical phase (~15 days before and after circular phase), mapping of selected areas (~40) at intermediate to high resolutions: 50 to <750 m/pix, bridging the gap in resolution between systematic mapping (MAJIS_GCO5000_global) and GCO ROIs (MAJIS_GCO500_HR).
Pointing: YS, NADIR
satellite orientation: MAJIS slit at a slant with the ground track except at the equator
Duration: from 35 min to 4H (Table 8 from budget report v2.1) | MAJIS |
MAJ_ICU | To monitor the radiometric performances of MAJIS using VISNIR and IR sources Specifically, there are several goals
A) tracking the evolution of the actual levels (before subtracting for CDS) in the digital dynamics (0-65535 at 100 kHz, 0-4095 at 1 MHz). Such an evolution could lead to adjust an offset which can be selected by TC (4 settings) so as to avoid reaching digital saturation for the read image before analog saturation.
B) tracking the evolution of the dark current and cosmetics (new hot / dead pixels)
C) tracking the evolution of the overall photometric response as a function of the signal (needed for the pipeline)
Pointing: MAJIS scan mirror oriented towards the ICU (8.5°)
Satellite orientation: Deep space
Duration: 10min | MAJIS |
MAJ_JovianRING_MOSAIC | Mosaicking the 2 ring ansa from 90000 to 230000 km. 3 overlapping cubes of 20 vertical lines performed by the scanner (or S/Cslew if compatible with JANUS). This requires re-pointing between individual cubes.
Pointing: OFF-NADIR, S/C pointing projected ring plane, S/C depointing required for the two ansa
Satellite orientation: Maintaining the horizontal orientation of MAJIS slit, MAJIS scan mode activated for vertical sampling (20 vertical lines) centered on the rings, S/C depointing required for mosaicking each ansa (3 overlapping cubes to perform a radial mosaic of one ansa of the rings with radial distance from 90000 to 230000 km)
Duration: 1200 sec (excluding the S/C repointings) | MAJIS |
MAJ_JUP_AURORAL_MAPPING | Jupiter Auroral Mapping
Scanning of the instrument slit over Jovian polar regions, from polar limb to approx. 50°N/S latitudes, with exposure times optimized for weak auroral emissions.
Note: similar to MAJIS_JUP_DISK_SCAN but for high latitudes during high inclination phase
Duration: typically, 40 min (200 lines <-> typical size of latitudes where polar ovals are observed) | MAJIS |
MAJ_JUP_DISK_MOSAIC | A series of several MAJIS_JUP_DISK_SCAN or MAJIS_JUP_DISK_SLEW
Spacecraft has to be re-pointed between individual acquisitions.
POinting type: YS, NADIR with offset around Y (‘ nadir offset MAJIS scan’’)
satellite orientation: HORIZONTAL (preferred)
Duration:
3 x (scan-duration + turnaround Y duration). Scan duration from 20 to 40 min depending on the distance from Jupiter. Turnaround ~50 min | MAJIS |
MAJ_JUP_DISK_SCAN | Observations of Jupiter clouds and spectroscopy of minor gases.
Scanning the instrument slit over Jovian disk (vertical direction) by means of internal pointing mirror, both dayside and nightside. Aims to cover at least the entire equatorial region (-30°:+30°) during low inclination phases and the polar regions during high inclination phase.
Duration: typically 20min/cube, max 30 min/cube, assuming 2.1 s per line | MAJIS |
MAJ_JUP_DISK_SLEW | Observations of Jupiter clouds and spectroscopy of minor gases.
Scanning the instrument slit over Jovian disk (vertical direction) by means of the S/C slew. aims to cover the entire equatorial region (-30°:+30°)
Pointing: OFF_NADIR, CONTINUOUS SLEW (« continuous S/C scan »)
Satellite orientation: HORIZONTAL
Duration: 20 min per cube | MAJIS |
MAJ_JUP_EVENT_MONITORING | Study of the evolution of unusual phenomena in Jupiter atmosphere, especially in their zonal evolution MAJIS will acquire several “subcubes” with limited number of lines (about 80) as follows:
1. a series of sub-cubes (from 1 to 4) is acquired with the scan mirror to get the coverage of a limited latitude region at all longitudes on the visible side of the planet. Satellite is re-pointed before acquiring each sub-cube
2. the series at previous point is repeated at fixed time intervals (in the order of 1 h, TBC) to monitor the temporal evolution.
Pointing type: YS, Series of OFF-NADIR pointings (‘off-nadir scan mode’)
satellite orientation: HORIZONTAL
Duration:
160 sec for each sub-cube.
Time between series defines actual temporal sampling and is variable (zero data rate here).
Total duration about 5 h (1/2 of rotation period) | MAJIS |
MAJ_JUP_HIGH_FREQ_MONITORING | The observing type is designed to study the evolution of atmospheric features at high temporal frequency as well as to map specific atmospheric features at regional scale.
Scanning of features on the Jovian disc, on dayside as well as on nightside, with limited latitudinal coverage.
MAJIS will acquire one or more several “subcubes” with a limited number of lines (about between 64 and 160)
Duration: between 84 and 315 s for each cube, assuming 2.1 s per line | MAJIS |
MAJ_JUP_LIMB_SCAN | The MAJIS pointing mirror is used to scan the atmosphere of Jupiter over the limb up to 1500km. Exposure times are optimized for weak limb emissions.
The scan mirror step of 1/10 MAJIS IFOV shall constrain the spatial sampling provides a spatial supersampling adequate to reconstruct, by deconvolution, the signal vertical profile at sub-pixel scale.
Observations consists in sets of max. 8 cubes at different latitudes, around the limb of the planet.
Duration: Typically 20 min for each cube (110 lines), assuming 11 s per line | MAJIS |
MAJ_JUP_LIMB_SLEW | The scan the atmosphere of Jupiter over the limb up to 3000k is performed with a specific slew of the S/C
Individual lines are largely overlapped to provide actual supersampling (x 10) in the spatial domain and allow sub-pixel resolution by deconvolution.
Typically, we have cubes of about 300 lines by 50 pixels (~7500 km)
Pointing type:
OFF-NADIR (nominal pointing position over the Jupiter limb), continuous tracking (‘track tangent limb’)
satellite orientation:LIMB TANGENT (MAJIS slit tangent to the limb), very slow s/c slew to get oversampling (10 lines corresponding to one pixel IFOV)
Duration: 55 min for each cube (300 lines) | MAJIS |
MAJ_JUP_STELLAR_OCC | MAJIS will acquire several “subcubes” (number depends upon planet's speed over the sky) around the (fixed) star position, at different angular distances between the star and the planet's limb during the ingress/egress.
Each sub-cube spans over several lines (around 6, less if S/C capability allows it) to compensate for possible pointing inaccuracies.
Bright far moons can be used instead of stars as sources to decrease the repetition integration (and therefore spatial sampling) as the orbital velocity ranges from ~ 5 km/s at apojove to ~ 13 km/s at perijove
satellite orientation: LIMB TANGENT (preferred, otherwise VERTICAL), to minimize straylight
duration:
About 10min
66 sec (max) for each subcube. Time interval between sub-cubes as small as possible for better vertical coverage. Total number of cubes depends upon relative angular speed between star and limb. | MAJIS |
MAJ_MainRING _HighPhase | Observations of the main rings (2 ansa) at high phase (forward scattering light), no tracking of azimuthal structure, no spatial binning to increase spatial resolution.
Pointing: OFF-NADIR, S/C pointing centered on the extremity of main rings, S/C depointing required for the two ansa
Satellite orientation: Maintaining the MAJIS slit parallel to radial axis of main rings, MAJIS scan mode activated for vertical sampling (20 vertical lines) centered on the rings
Duration: 400 sec (excluding the S/C repointing to the other ansae) | MAJIS |
MAJ_MainRING _LowPhase | Observations of the main rings (2 ansa), no tracking of azimuthal structure, 20 vertical lines
pointing: OFF-NADIR, S/C pointing centered on the extremity of main rings, S/C depointing required for the two ansa
Satellite orientation: Maintaining the MAJIS slit parallel to radial axis of main rings, MAJIS scan mode activated for vertical sampling centered on the rings (20 vertical lines)
Duration:400 sec (excluding the S/C repointing to the other ansae) | MAJIS |
MAJ_MainRING _PhaseCurve | Observations of the main rings at various phase angles (N angles), one ansae (always the same), 20 vertical lines
Pointing: S/C pointing ring plane at 1.8 R_J (extremity of main rings)
Satellite orientation: OFF-NADIR, Ring plane while maintaining horizontal orientation of MAJIS slit, MAJIS scan mode activated for vertical sampling centered on the rings (20 lines)
Duration: 200 sec for one observations at a given phase angle | MAJIS |
MAJ_Ring_Occultation | Observation of a star occulted by the rings
Scan windowing of 9 lines centered on the star (1 scan step = 1/3 MAJIS IFOV) possible
Pointing: Inertial. For each occultation, transit of TBD min
Satellite orientation: Inertial pointing of the S/C towards the position of the star to maintain MAJIS slit fixed on it. These occultation observations need to be consolidated in the future (star atlas, signal, Tint, S/C inertial capabilities). Scan mirror can be used to mitigate APE drift | MAJIS |
MAJ_SAFE | Initiated after ASW loading
All channels are off and no PE HK are generated. Only ME HK are generated (only DPU ON)
From SAFE it is possible 1) to switch OFF MAJIS, 2) to change the status of MAJIS to DIAG1 or SERVICE mode
Duration: less than 5min | MAJIS |
MAJ_SAT_DISK_SCAN | Observation of a distant satellite dayside or nightside surface. Satellite offset required for pointing then disk coverage is achieved using the internal pointing mirror scanning in the Y (N-S) direction.
Pointing: NADIR-P with possible offset around Y, YS, MAJIS scan (‘Nadir scan’).
Satellite orientation: MAJIS slit perpendicular to the ground-track
Duration: 30min | MAJIS |
MAJ_SAT_DISK_SLEW | Flyby observations of the satellite surface with vertical (N-S) slews across track, during yaw-steering phase. One or two slews (pole to pole) necessary to complete dayside coverage. Satellite offset around Y-axis (E-W) before each observation, then satellite offsets around X axis (N-S) between each slit acquisition.
Pointing: NADIR Pointing, YS, S/C scan (slew) with offset around Y (‘mosaic mode’ tbc). MAJIS slit perpendicular to the ground-track.
Satellite orientation: MAJIS slit perpendicular to the ground-track
Duration: 30 min | MAJIS |
MAJ_SAT_LIMB_SCAN | Flyby observations of the satellite dayside or nightside limbs with vertical (N-S) slews across track, during yaw-steering phase. Satellite offsets to limb around Y-axis (E-W) before each observation, then satellite offsets around X axis (N-S) between each slit acquisition or continuous slew pointing.
Pointing: S/C slew scan centred a limb ( ‘Limb slew scan mode’).
Satelliteo orientation: Slit tangent to the limb
Duration: 60min | MAJIS |
MAJ_SAT_LIMB_TRACK | Continuous stare observation of a satellite limb during flyby using inertial pointing from satellite, dayside or nightside. Additional offsets within limb by means of internal pointing mirror. Scanning with MAJIS internal mirror. (--> ‘track limb’).
Pointing: S/C limb tracking (‘track limb’)
satellite otientation: SLIT tangent to the limb (slit not aligned with S/C motion)
Duration: 60min | MAJIS |
MAJ_SERVICE | MAJIS in service MODE (1 or 2 channels with FPE/FPA off + AUX w/o loads)
SERVICE Mode as soon as one or two channels are switched ON (PE and AUX)
From SERVICE, it is possible to return to SAFE mode or to change the status of MAJIS to DIAG2, DIAG3 or SCIENCE
Duration: less than 10min | MAJIS |
MAJ_STANDBY | After switch-on of MAJIS, the Boot SW automatically starts, and performs the primary boot from the PROM (Init fugitive BSW mode).
After processor modules initialization, the Boot software goes to STANDBY mode. By default, the ASW Image0 (stored in MRAM0 = ASM0) is autonomously loaded after a timeout of 30 seconds. MAJIS then enters into ASW init Mode and then into SAFE mode.
In STANDBY Mode, all channels are off, and only DPU HK SID1 are received.
MAJIS needs to be maintained in STANDBY mode using the TC(17,1) in the following cases :
- upload (using service 6) of new ASW images (or CUSW, or firmware) into MRAM: FCP-MAJ-070 describes the maintenance process.
- upload a new BROWSE Table FCP-MAJ-060 into MRAM
- select ASW Image1 and then start ASW Image 1 instead of teh default ASW Image0. FCP-MAJ-062
- any other update of MRAM using service 6 | MAJIS |
NAVCAM_DVOL_BLOCK | | JUICE |
PEP_FLYBY_APPROACH | Moon environment monitoring: plasma moments, energetic particle spectra and pitch angle distributions (low time resolution). Moon imaging (JNA) & Europa torus (JNA imaging + in-situ) if near Europa. High altitude exosphere (NIM)
Sensors on: all
Corotation in JEI or JDC FoV
Full pitch angle coverage (JDC, JEI, JoEE, JENI ions)
Moon in JNA FoV
Angle of NIM_THERMAL_1 or THERMAL_2 from
JUICE_EUROPA_RAM or JUICE_GANYMEDE_RAM or JUICE_CALLISTO_RAM velocity less than 60 deg | PEP |
PEP_FLYBY_CLOSEST_APPROACH | Local moon-magnetosphere interaction observation: plasma moments, energetic particle spectra and pitch angle distributions (high time resolution for short term variations)
Europa imaging (JNA). Dense exosphere (NIM)
Sensors on: all
Corotation in JEI or JDC FoV
Full pitch angle coverage (JDC, JEI, JoEE, JENI)
Moon in JNA FoV
Angle of NIM_NEUION_S0 from JUICE_EUROPA_RAM or JUICE_GANYMEDE_RAM or JUICE_CALLISTO_RAM velocity less than 5 deg at CA
Solar panel rotation angle (SADM) SADM > 74° or
SADM < -74°
Moon in JNA FoV | PEP |
PEP_FLYBY_DEPARTURE | Europa environment monitoring: plasma moments, energetic particle spectra and pitch angle distributions (high time resolution for short term variations)
Europa imaging (JNA) & Europa torus (JNA imaging + in-situ)
All sensors on except NIM (in standby or off)
Corotation in JEI or JDC FoV
Full pitch angle coverage (JDC, JEI, JoEE, JENI) | PEP |
PEP_FLYBY_FAR_APPROACH_LOW_RATE | Moon environment monitoring: plasma moments, energetic particle spectra and pitch angle distributions (low time resolution). Europa torus (JNA imaging + in-situ) if near Europa
Sensors on: all
Corotation in JEI or JDC FoV
Full pitch angle coverage (JDC, JEI, JoEE, JENI ions) | PEP |
PEP_FLYBY_FAR_APPROACH_MEDIUM_RATE | Moon environment monitoring: plasma moments, energetic particle spectra and pitch angle distributions (low time resolution). Europa torus (JNA imaging + in-situ) if near Europa
Sensors on: all
Corotation in JEI or JDC FoV
Full pitch angle coverage (JDC, JEI, JoEE, JENI ions)
Moon in JNA FoV
Angle of NIM_THERMAL_1 or THERMAL_2 from
JUICE_EUROPA_RAM or JUICE_GANYMEDE_RAM or JUICE_CALLISTO_RAM velocity less than 60 deg | PEP |
PEP_FLYBY_FAR_APPROACH_NIM_BACKGROUND | NIM background measurements part of switch on procedure.
Moon environment monitoring: plasma moments, energetic particle spectra and pitch angle distributions (low time resolution). Europa torus (JNA imaging + in-situ) if near Europa
Sensors on: all
Corotation in JEI or JDC FoV
Full pitch angle coverage (JDC, JEI, JoEE, JENI ions) | PEP |
PEP_FLYBY_FAR_DEPARTURE | | PEP |
PEP_FLYBY_FAR_DEPARTURE_LOW_RATE | Europa environment monitoring: plasma moments, energetic particle spectra and pitch angle distributions (high time resolution for short term variations)
Europa imaging (JNA) & Europa torus (JNA imaging + in-situ)
All sensors on except NIM (in standby or off).
Corotation in JEI or JDC FoV
Full pitch angle coverage (JDC, JEI, JoEE, JENI) | PEP |
PEP_FLYBY_FAR_DEPARTURE_LOW_RATE_ENA | Europa environment monitoring: plasma moments, energetic particle spectra and pitch angle distributions (high time resolution for short term variations)
Europa imaging (JNA) & Europa torus (JNA imaging + in-situ)
All sensors on except NIM (in standby or off). JENI in Combo mode (half in ion mode, half imaging)
NIM in ram direction (X-Y S/C plane) | PEP |
PEP_GANYMEDE_IN_SITU_BURST_1 | Burst in-situ mode, Ganymede phase. CA of moon flybys later in the mission (higher power consumption) Short duration events (e.g. boundary crossings). All instruments on, NIM in neutral mode (response of ionosphere to charged particles). PEP Hi on, all in-situ
PEPLo Sensors ON: All sensors ON, NIM neutral mode, JNA ion mode
PEPHi Sensors ON: JENI_Ion, JoEE | PEP |
PEP_GANYMEDE_IN_SITU_BURST_2 | Burst in-situ mode, Ganymede phase. CA of moon flybys later in the mission (higher power consumption) Short duration events (e.g. boundary crossings). All instruments on, NIM in neutral mode (response of ionosphere to charged particles). PEP Hi on, all in-situ
PEPLo Sensors ON: All sensors ON, NIM, JNA ion mode
PEPHi Sensors ON: JENI_Ion, JoEE | PEP |
PEP_GANYMEDE_IN_SITU_LOW_1 | Same as PEP_GANYMEDE_IN_SITU_NOMINAL_3 but with low performance in JDC, JEI to limit power (JEI 8 sectors, JDC low power). NIM, JNA off. Low power mode for Ganymede, good for long duration surveys
PEP Hi on, all in-situ
PEPLo Sensors ON: JDC_LP, JEI (8 sectors)
PEPHi Sensors ON: JENI_Ion, JoEE | PEP |
PEP_GANYMEDE_IN_SITU_LOW_2 | Same as PEP_GANYMEDE_IN_SITU_NOMINAL_1 but with low performance in JDC, JEI to limit power (JE 4 sectors, JDC low power). NIM neutral, JNA on. Low power mode for Ganymede, good for long duration surveys with multiple instruments. PEP Hi on, all in-situ.
PEPLo Sensors ON: JEI: 4 sectors, JDC: LP, NIM: Neutral mode
PEPHi Sensors ON: JENI_Ion, JoEE | PEP |
PEP_GANYMEDE_IN_SITU_LOW_3 | Same as PEP_GANYMEDE_IN_SITU_NOMINAL_1 but with low performance in JDC, JEI to limit power (JEI 4 sectors, JDC low power). NIM ion, JNA on. Low power mode for Ganymede, good for long duration surveys with multiple instruments. PEP Hi on, all in-situ
PEPLo Sensors ON: JEI: 4 sectors, JDC: LP, NIM: Ion mode
PEPHi Sensors ON: JENI_Ion, JoEE | PEP |
PEP_GANYMEDE_IN_SITU_LOW_4 | Same as PEP_GANYMEDE_IN_SITU_NOMINAL_1 but with low performance in JDC, JEI to limit power (JEI 4 sectors, JDC low power). NIM ion, JNA on. Low power mode for Ganymede, good for long duration surveys with multiple instruments. PEP Hi on, all in-situ
PEPLo Sensors ON: JEI: 4 sectors, JDC: LP, NIM: Ion mode
PEPHi Sensors ON: JENI_Ion, JoEE | PEP |
PEP_GANYMEDE_IN_SITU_LOW_5 | Same as PEP_GANYMEDE_IN_SITU_LOW_1 but with lowest performance in JDC, JEI for max power savings while PEP-Lo is no (JEI 4 sectors, JDC low power). NIM, JNA off. Low power mode for Ganymede, good for long duration surveys. PEP Hi on, all in-situ
PEPLo Sensors ON: JDC_LP, JEI 4 sectors, JNA & NIM off
PEPHi Sensors ON: JENI_Ion, JoEE | PEP |
PEP_GANYMEDE_IN_SITU_LOW_6 | Mode with only NIM on (neutral) from PEP-Lo. Required for avoiding switching on/off NIM once per day during downlinks. Good for long surveys of the exosphere. PEP Hi on, all in-situ.
PEPLo Sensors ON: NIM neutral on, only
PEPHi Sensors ON: JENI_Ion, JoEE | PEP |
PEP_GANYMEDE_IN_SITU_LOW_7 | Mode with only NIM on (ion) from PEP-Lo. Required for avoiding switching on/off NIM once per day during downlinks. Good for long surveys of the ionosphere. PEP Hi on, all in-situ
PEPLo Sensors ON: NIM ion on, only
PEPHi Sensors ON: JENI_Ion, JoEE | PEP |
PEP_GANYMEDE_IN_SITU_LOW_8 | Only PEP-Hi on (all in-situ), max power savings
PEPLo Sensors ON: None
PEPHi Sensors ON: JENI_Ion, JoEE | PEP |
PEP_GANYMEDE_IN_SITU_NOMINAL_1 | Regular in-situ mode, ganymede phase. CA of moon flybys later in the mission (higher power consumption). Good for high quality, extended survey. All instruments on, NIM in neutral mode (response of exosphere to charged particles). PEP Hi on, all in-situ
PEPLo Sensors ON: All sensors ON, NIM neutral mode, JNA ion mode
PEPHi Sensors ON: JENI_Ion, JoEE | PEP |
PEP_GANYMEDE_IN_SITU_NOMINAL_2 | Regular in-situ mode, ganymede phase. CA of moon flybys later in the mission (higher power consumption). Good for high quality, extended survey. All instruments on, NIM in ion mode (response of ionosphere to charged particles). PEP Hi on, all in-situ
PEPLo Sensors ON: All sensors ON, NIM, JNA ion mode
PEPHi Sensors ON: JENI_Ion, JoEE | PEP |
PEP_GANYMEDE_IN_SITU_NOMINAL_3 | Regular in-situ mode, ganymede phase. CA of moon flybys later in the mission (higher power consumption). Good for high quality, extended survey in charged particles. NIM, JNA off. PEP Hi on, all in-situ.
PEPLo Sensors ON: JDC, JEI on, JNA & NIM off
PEPHi Sensors ON: JENI_Ion, JoEE | PEP |
PEP_IDLE | PEP in IDLE mode | PEP |
PEP_JUPITER_EQUATORIAL_TORUS_CROSSING | All sensors, except JNA, on in medium to low rates. Prime objective is for NIM to measure torus composition in-situ. Other sensors to measure indicators that can be used to constrain the densities. Applies also to Jupiter High Inclination for now. | PEP |
PEP_JUPITER_IN_SITU_BURST_1 | Burst in-situ mode for magnetosphere, CA of moon flybys (if NIM offl), Short duration events (magnetopause/bow shock crossings, injection events, moon wakes/microsignatures)
PEPLo Sensors ON: JDC, JEI
PEPHi Sensors ON: JENI_Ion, JoEE | PEP |
PEP_JUPITER_IN_SITU_IMAGING_BURST_1 | Burst in-situ mode, magnetosphere. CA of moon flybys with JNA/JENI imaging (if NIM off)
PEPLo Sensors ON: JDC, JEI, JNA
PEPHi Sensors ON: Option 1: JENI_Combo, JoEE. Option 2: JENI_ENA, JoEE | PEP |
PEP_JUPITER_IN_SITU_IMAGING_LOW_1 | Low power in-situ & ENA imaging mode (e.g. downlink, non-prime/low priority science segments).
PEPLo Sensors ON: JDC_LP, JEI (4 sectors), JNA
PEPHi Sensors ON: Option 1: JENI_Combo, JoEE. Option 2: JENI_ENA, JoEE | PEP |
PEP_JUPITER_IN_SITU_IMAGING_NOMINAL_1 | Regular magnetosphere in-situ & ENA imaging monitoring mode. Can work on flybys, if NIM off.
PEPLo Sensors ON: JDC_LP, JEI (8 sectors), JNA
PEPHi Sensors ON: Option 1: JENI_Combo, JoEE. Option 2: JENI_ENA, JoEE | PEP |
PEP_JUPITER_IN_SITU_LOW_1 | Low power in-situ mode (e.g. downlink, non-prime/low priority science sgments)
PEPLo Sensors ON: JDC_LP, JEI (8 sectors)
PEPHi Sensors ON: JENI_Ion, JoEE | PEP |